Toilet Repair Plumber Near Me

Our Toilet Repair Services Key Benefits

Locally Owned and Operated
High-Quality Workmanship
Bonded and Insured
Courteous Customer Services
Flat Rates with Upfront Estimates
Licensed Plumbing Professionals

Plumbing is what we do

Toilet Repair Services Near Orlando, Florida

Holden Heights, Edgewood, Fairview Shores, Conway, Pine Castle, Azalea Park, Winter Park, Orlovista, Eatonville, Oak Ridge

When things go wrong with your home toilet, it could be one of the most common– and disturbing– plumbing problems you might encounter in your home. Whether it is overflowing or running continuously, a toilet repair is an issue you can not put aside.

It would be best if you always try and maintain them in good working order as they are among the most considerable fixtures in a plumbing system. We do not pay them much thought till something goes wrong and they quit working.

The feared clogged-up toilet is among homeowners’ most common domestic challenges. Many will attempt to repair the issue, only to find that the repair did not work or that the issue reappeared.

When the issue requires more than just a plunger service, it’s best to call a local plumber near me for all toilet repair or installation needs. With years of experience servicing Orange County, Florida locations, our local plumbing expert team can take care of toilet repair quickly and efficiently, and at a reasonable cost.

Call us today and schedule a non-commitment appointment.

Some jobs are better left to the pros...

Get No-Commitment Estimates For Your Project in Orange County, Florida

Call A Pro Today

Most Common Problems with Toilets in Homes

Plenty of toilet repairs, installations, and services are best left for the pros to deal with. However, not all services require emergency plumbing services.

Allow us to go through a few of the typical issues faced by consumers who have contacted us for ideas on how to deal with them:

Groaning sounds:

If you hear moaning noises from a toilet, it could be due to an increase in water pressure, which makes a valve shudder or shake.

Random or consistent flushing:

Either of these two issues will possibly cause the unit to flush and start filling up on its own:

the refill tube is too long, or
a leaking flapper

This flushing at random leads to water damage and waste, resulting in a higher monthly water service bill.

Compound flushing:

Perhaps you only flush once; however, the toilet flushes two times or even 3 times. A high water level is typically the source of this issue. Changing the float control within the tank will typically repair this issue.

Water leaking into the bowl, or “Phantom Flushes”:

A slow leak from the tank into the bowl is the source of the issue here. A malfunctioning flapper or flapper seat is unquestionably to blame.

Replacing a worn or broken flapper is the best solution to avoid plumbing issues. Empty the water tank, clean and check the seat, then replace the flapper.

Sluggish flushes:

A low water level or the lift chain that links the flush handle and the flapper valve causes a toilet only to flush partially. Loosen the lift chain to let the flapper settle down correctly inside the bowl.

Base leakages:

The gasket made of wax between the drain pipe at the base of the unit must be replaced if it leaks when flushed. This procedure requires an expert plumbing service.

Not flushing totally:

Check if the lift chain has any slack, and make adjustments as needed.
Check for a correct water level in the tank.
After that, ensure that the flapper is fitted correctly and is the best size and type for the unit.

The Bowl Empties Slow:

Obstructed holes under the bowl’s surface area are the most typical cause of a slow-emptying bowl, also referred to as a bad flush. To clean out any clutter, carefully poke each flush hole with a bent piece of wire.

If you are still unable to resolve these issues, it will be best to contact a local plumber near me.

the best solutions

Toilet Repair Services

24/7 Emergency Plumbing Service

Pro Plumbing Service Tips for Fixing Typical Toilet Issue Yourself

A toilet consists of two major parts: the bowl unit, which rests on the flooring, and the top storage tank which holds the water. The bowl is a solid drain piece of the fixture made of porcelain with no moving parts.

Few repairs involve the bowl, with a few exceptions. On the other hand, the storage tank is where two essential valves exist and the handle for flushing. The storage tank is where most of the toilet repairs occur.

You will be surprised to learn that most problems are fairly easy to fix without the need to call an emergency plumber.

Running Toilet Repair Service:

If you’ve tried out a new flapper for a running toilet and it still runs, do not give up hope. Here’s a solution that ensures it works.

Few home annoyances are somewhat as irritating as the sound of continuously running water. If you hear filling up frequently, or if you hear the consistent hiss of running water, the flapper in the unit might be leaking.

The flapper (also known as the “flush valve seal”) is the plug that falls against the drain opening (flush valve drain seat) on the bottom of the storage tank. It holds water till the next time you flush. When flappers or flush valve seats wear, water drips out, creating the valve to open and refill the storage tank.

Step 1: Changing Flapper:

First, remove the old flapper and bring it with you to the hardware shop or home center to get an identical one.

Note: Occasionally, a new flapper does not fix the issue. If you have tried changing the flapper, but it still runs, the flush valve seat is possibly rough or pitted.

You can change the complete flush flapper valve; nonetheless, it is not an easy job, and it might require the experience of a plumber near Orlando, Florida.

Step 2: Flapper Set with Flush Seat Repairing:

If changing the flapper alone failed to work, look for a flapper set with a flush seat repair.

Note: You want to purchase a Flush valve repair set. The set has a flapper and matching seat that you stick to the broken seat with the glue supplied.

First, shut the water to the toilet.
Hold the flapper open while flushing to allow the remaining water to drain from the storage tank.
Use a sponge to remove the water that remains entirely.
Follow the included instructions to set up the new flapper valve seat.
- Pro tip: If the unit uses 3.5 gallons or less of water per flush, you will need a kit that includes a plastic cup to change the flapper’s time to stay open. If your unit utilizes more than this, get rid of the timing cup.
  Set up the new flapper.
With the flapper down, adjust the chain length, so it’s somewhat relaxed.
Turn on the water to check the flush.

Note: You may need to fiddle with the chain length-size to get the flapper working correctly.

When finished, remove the excess chain to prevent it from getting stuck under the flapper.

Toilet Repair Services: Broken Handle

If shaking the handle does not stop your toilet from running, any of these straightforward repairs possibly will.

The handle is a primary device– just a few things can malfunction and need to be repaired. The solution is easier than you think.

Step 1: Loose Handle:

If the handle is loose, the installation of a new one is fairly easy. Tighten up the nut and washer inside the storage tank with a pair of pliers without over-tighten it; you could strip the threads or, even worse, damage the porcelain storage tank.

If the handle sticks in the down flush position, it may not be installed properly. Loosen up the nut washer, reposition the handle to align with the top side of the storage tank, and re-tighten the nut.

Step 2: Stripped Threads:

If the nut does not tighten up or keeps coming loose, it’s a sign that the nut threads are stripped. For a quick repair, wrap the threads on the handle screw with “plumber’s tape” or electrical tape.

Then, slide the washer and nut back on and tighten up the nut. It is often best to replace the handle with a brand-new one if the threads are too damaged or broken.

Step 3: Handle Arm:

Check out the handle arm for issues, splits, or breaks.
If there are issues, change the entire handle and the arm assembly.
- Pro tip: Remember where your handle mounts on the storage tank before purchasing a replacement handle. There are numerous kinds: front mount left, front mount right, front mount universal, and side mount.

Tip 4: The Chain:

Suppose the handle appears to be running correctly, yet the toilet still does not flush. In that case, the chain attaching the handle arm to the flapper could be detached or damaged.

- Pro Tip: Before working on the chain, empty the storage tank, shut off the water valve, and pull up the flapper, letting the water to drain.

If the chain detaches from the handle arm, reconnect the chain from the flapper into the holes on the handle arm, utilizing the chain hook.
Leave a little slack in the chain.
If the chain detaches from the flapper, reconnect the chain to the flapper.
If the chain or the flapper is defective, change it.

Buying Tips for Toilets

Tired of your old, dripping, water hog of a toilet and want to buy a new one? A toilet replacement is not a major job and today you’ll find water-efficient units with an array of options. Use the following tips for the next time you go shopping for a new unit.

Insulated storage tank:

If summers are moist where you live, and you do not have air conditioning, you’ve possibly noticed “sweating moisture” quite a bit on the side of the unit. Condensation forming on the outside of a toilet can drip down, making a water mess and even rotting your flooring.

Today, most toilets are made available with insulated tanks to prevent condensation issues. Look into this option if you have “sweating” problems.

Bowl height:

Bowl height is the distance from the flooring to the top of the bowl’s edge– the standard height is 14 to 15 inches. Yet today, you’ll find units 16 to 18 inches high, commonly called “comfort level” “ADA height” or something similar.

The additional heights available make getting on and off much more accessible and comfortable for many people, especially aging people. Designs for youngsters with heights of 10 to 14 inches are also available.

One-piece vs. two-piece:

A two-piece (a separate storage tank and bowl) is the most common style in houses. Yet one-piece designs are offered. Two-piece designs are generally less expensive; one-piece designs typically have shorter storage tanks and are much easier to clean up.

One-piece designs are the choice of many property owners because of their smooth, sleek look.

Cost:

When it pertains to toilets, expensive does not immediately suggest better efficiency. Several of the best models we have tested were reasonably cost-effective and performed well. In comparison, costlier ones were only marginally efficient.

Color:

Fashion is fickle. Stick to a white or off-white color style to avoid being stuck to a color you’ll resent a few years later.

Flush-handle location:

If you have a large bathroom and have ample space above or beside your toilet, this perhaps isn’t all that crucial. Make sure to pick a style with a top handle or one opposite the wall if the space is limited.

Purchasing a proper style is very important, to spare yourself a return trip to the store, so pay attention when choosing style options.

Rough-in:

The “rough-in” measurement is the distance between the flange screws that anchors the toilet bowl to the flooring and the wall surface behind it. A 12-inch “rough-in” is the most common measurement; nonetheless, in some older houses, you could have a ten-inch or even a 14-inch “rough-in.”

Tip: Make sure to measure your “rough-in” and always account for the thickness of your baseboard, paneling, or tile backing before purchasing the unit.

Bowl shape:

Many unit designs marketed today have either round-front bowls or elongated-front bowls.

Round-front bowls are great if the area is tight.
Elongated bowls have a more extended edge– as much as two-inch longer– and require more space.

On the plus side, elongated bowls are typically much more comfortable for adult use which helps increase health and wellness. Assess your vendor’s websites for bowl measurements, and measure your space before picking the bowl shape.

Footprint:

If you install a new toilet with a smaller sized storage tank, you might need to repaint the part of the wall surface area covered by the old storage tank.

The same will apply if the old unit style had a big footprint on the floor, you might need to patch and fix the flooring part surrounded by the footprint of the old unit. You may additionally need to change the entire flooring before setting up a new unit.